전체 선택해제
총 18건 검색
본문검색 결과만 보기
-
Improvement of the Low-Speed Friction Characteristics of a Hydraulic Piston Pump by PVD-Coating of TiN
Hong. Yeh-Sun, Lee. Sang-Yul, Kim. Sung-Hun, Lim. Hyun-Sik 대한기계학회 Journal of mechanical science and technology 8 Pages
대한기계학회 Journal of mechanical science and technology 2006, Vol.20 No.3 358-365 (8 pages)
-
Modifications of mechanical, thermal, and electrical characteristics of epoxy through dispersion of multi-walled carbon nanotubes in supercritical carbon dioxide
MGH ZAIDI, Sanjeev Joshi, Manoj Kumar, Deepak Sharma, Ashwin Kumar, Sarfaraz Alam, Prakash Sah 한국탄소학회 Carbon Letters 10 Pages
한국탄소학회 Carbon Letters 2013, Vol.14 No.4 4 218-227 (10 pages)
-
TiN Ion-Plating이 교정용 브라켓의 접착강도에 미치는 영향
김석용(Seok-Yong KIM), 권오원(Oh-Won KWON), 김교환(Kyo-Han KIM) 대한치과교정학회 The Korean Journal of Orthodontics 15 Pages
대한치과교정학회 The Korean Journal of Orthodontics 1997, 제 27권 제 1호 13 157-171 (15 pages)
TiN ion-plating이 교정용 브라켓의 접착강도에 미치는 영향을 알아보기 위하여 세 종류의 서로 다른 기저면형태를 가지는 스테인레스 스틸제의 브라켓을 선택하고, TiN ion-plating 된 브라켓과 ion-plating 되지 않은 브라켓을 치아에 접착시켰을 때 초기 및 장기 접착강도, 접착계면의 주사전자현미경 관찰, 파단면의 주사전자 현미경과 관찰을 비교 분석하여 다음과 같은 결론을 얻었다. • TiN ion-plating을 하지 않은 경우 24시간 후의 접착강도는 Micro-Loc 형이 5.89±1.77 MPa, Foil Mesh 4.27±1.12 MPa,... -
Hole quality assessment of drilled CFRP and CFRP-Ti stacks holes using polycrystalline diamond (PCD) tools
Dave Kim, Aaron Beal, Kiweon Kang, Sang-Young Kim 한국탄소학회 Carbon Letters 8 Pages
한국탄소학회 Carbon Letters 2017, Vol.23 1 1-8 (8 pages)
Polycrystalline diamond (PCD) tools possessing high hardness and abrasive wear resistance are particularly suited for drilling of carbon fiber reinforced plastic (CFRP) composites, where tool life and consistent hole quality are important. While PCD presents superior performance when drilling CFRP, it is unclear how it performs when drilling multi-stack materials such as CFRP-titanium (Ti) stacks. This comparative study aims to investigate drilling of a Ti plate stacked on a CFRP panel when... -
Thermo-electrical properties of randomly oriented carbon/carbon composite
Thakur Sudesh Kumar Raunija, N. Supriya 한국탄소학회 Carbon Letters 11 Pages
한국탄소학회 Carbon Letters 2017, Vol.22 3 25-35 (11 pages)
The aim of the work was to investigate the thermo-electrical properties of low cost and rapidly produced randomly oriented carbon/carbon (C/C) composite. The composite body was fabricated by combining the high-pressure hot-pressing (HP) method with the lowpressure impregnation thermosetting carbonization (ITC) method. After the ITC method step selected samples were graphitized at 3000°C. Detailed characterization of the samples’ physical properties and thermal properties, including thermal... -
Tribological properties of carbon fiber-reinforced aluminum composites processed by spark plasma sintering
Ki Hoon Jung, Seungjin Nam, Sung-Soo Kang, Bon-Cheol Ku, Yun Hyuk Bang, Jun Yeon Hwang 한국탄소학회 Carbon Letters 4 Pages
한국탄소학회 Carbon Letters 2017, Vol.21 14 103-106 (4 pages)
The development of light-weight and high-strength materials have gained attention to meet the evergrowing demands for safer and fuel-efficient automobiles. Thus, the importance and applications of composite materials are gradually increasing [1]. In the field of metal-matrix composite manufacturing, reinforcing agents are added to the metal matrix in the form of powders, whiskers, and fibers to improve the mechanical properties of metals [2]. Fibers have been used since the 1950s as structural... -
Effects of cross-linking methods for polyethylene-based carbon fibers: review
Kwan-Woo Kim, Hye-Min Lee, Jeong-Hun An, Byoung-Suhk Kim, Byung-Gak Min, Shin-Jae Kang, Kay-Hyeok An, Byung-Joo Kim 한국탄소학회 Carbon Letters 24 Pages
한국탄소학회 Carbon Letters 2015, Vol.16 No.3 2 147-170 (24 pages)
In recent decades, there has been an increasing interest in the use of carbon fiber reinforced plastic (CFRP) in aerospace, renewable energy and other industries, due to its low weight and relatively good mechanical properties compared with traditional metals. However, due to the high cost of petroleum-based precursors and their associated processing costs, CF remains a specialty product and as such has been limited to use in high-end aerospace, sporting goods, automotive, and specialist... -
Influence of hot-pressing pressure on the densification of short-carbon-fiber-reinforced, randomly oriented carbon/carbon composite
Thakur Sudesh Kumar Raunija and Sharad Chandra Sharma 한국탄소학회 Carbon Letters 9 Pages
한국탄소학회 Carbon Letters 2015, Vol.16 No.1 4 25-33 (9 pages)
The prime objective of this research was to study the influence of hot-pressing pressure and matrix-to-reinforcement ratio on the densification of short-carbon-fiber-reinforced, randomly oriented carbon/carbon-composite. Secondary objectives included determination of the physical and mechanical properties of the resulting composite. The ‘hybrid carbon-fiberreinforced mesophase-pitch-derived carbon-matrix’ composite was fabricated by hot pressing. During hot pressing, pressure was varied from 5... -
Microwave heating of carbon-based solid materials
Teawon Kim, Jaegeun Lee, Kun Hong Lee 한국탄소학회 Carbon Letters 10 Pages
한국탄소학회 Carbon Letters 2014, Vol.15 No.1 2 15-24 (10 pages)
As a part of the electromagnetic spectrum, microwaves heat materials fast and efficiently via direct energy transfer, while conventional heating methods rely on conduction and convection. To date, the use of microwave heating in the research of carbon-based materials has been mainly limited to liquid solutions. However, more rapid and efficient heating is possible in electron-rich solid materials, because the target materials absorb the energy of microwaves effectively and exclusively.... -
사축식 유압 피스톤 펌프의 저속 마찰 특성 개선
홍예선, 이상율, 김치붕, 김성훈, 임현식, 김성대, Hong. Yeh-Sun, Lee. Sang-Yul, Kim. Chi-Bung, Kim. Sung-Hoon, Rhim. Hyeon-Sik, Kim. Sung-Dae 유공압시스템학회 유공압시스템학회논문집 7 Pages
유공압시스템학회 유공압시스템학회논문집 2004, Vol.1 No.3 7-13 (7 pages)
-
도재브라켓의 제거방법에 따른 법랑질표면의 주사전자현미경학적 관찰
박미숙(Mi-Suk Park), 윤영주(Young-Jooh Yoon), 김광원(Kwang-Won Kim) 대한치과교정학회 The Korean Journal of Orthodontics 10 Pages
대한치과교정학회 The Korean Journal of Orthodontics 1996, 제 26권 제 5호 13 613-622 (10 pages)
도재브라켓의 제거방법에 따라 법랑질표면에 미치는 영향을 비교 평가하기 위하여 80개의 발거된 소구치를 대상으로 통법에 의해 도재브라켓을 부착시키고 일 주일후 각각 40개의 기계적 방법에 의한 제거군과 전기열전도 방법에 의한 제거군으로 구분하여 도재브라켓의 제거물 유도한 후, 그 탈락양상 및 도재브라켓과 법랑질 표면의 주사전자현미경 관찰을 시행하였으며, 전기열전도 방법에 의한 제거군을 다시 각각 10개씩 고속 tungsten carbide bur에 의한 연마군, 저속 sof-lex disc에 의한 연마군, 고속 resin polishing bur에... -
Effects of coal tar pitch addition on the wear behavior of carbon/carbon composites
Young Chan Jung, Duk Soo Kang, Kyong Yop Rhee, Soo Jin Park, David Hui 한국탄소학회 Carbon Letters 4 Pages
한국탄소학회 Carbon Letters 2016, Vol.20 9 62-65 (4 pages)
Carbon/carbon (C/C) composites are acknowledged as high performance materials because of their good mechanical properties such as wear resistance, even at the higher temperature, due to their low thermal expansion [1-5]. Their hardness and light weight in addition to their superior mechanical properties at high temperature make C/C composites the best material to make brakes for aircrafts and other high weight vehicles. Accordingly, a number of studies have been conducted on the performance of... -
Bulk graphite: materials and manufacturing process
Sang-Min Lee, Dong-Su Kang and Jea-Seung Roh 한국탄소학회 Carbon Letters 12 Pages
한국탄소학회 Carbon Letters 2015, Vol.16 No.3 1 135-146 (12 pages)
Graphite can be classified into natural graphite from mines and artificial graphite. Due to its outstanding properties such as light weight, thermal resistance, electrical conductivity, thermal conductivity, chemical stability, and high-temperature strength, artificial graphite is used across various industries in powder form and bulk form. Artificial graphite of powder form is usually used as anode materials for secondary cells, while artificial graphite of bulk form is used in steelmaking... -
Fabrication and Applications of Carbon Nanotube Fibers
Hungo Choo, Yeonsu Jung, Youngjin Jeong, Hwan Chul Kim, Bon-Cheol Ku 한국탄소학회 Carbon Letters 14 Pages
한국탄소학회 Carbon Letters 2012, Vol.13 No.4 1 191-204 (14 pages)
-
Reform Policy Directions for Vocational Education in Korea
Suk-Min Chang 한국교육학회 한국교육학회 학술대회논문집 28 Pages
한국교육학회 한국교육학회 학술대회논문집 KSSE Inter 17 394-421 (28 pages)
