기관회원 [로그인]
소속기관에서 받은 아이디, 비밀번호를 입력해 주세요.
개인회원 [로그인]

비회원 구매시 입력하신 핸드폰번호를 입력해 주세요.
본인 인증 후 구매내역을 확인하실 수 있습니다.

회원가입
서지반출
개인휴대통신에서 이동국의 수신성능개선을 위한 시스템 분석
[STEP1]서지반출 형식 선택
파일형식
@
서지도구
SNS
기타
[STEP2]서지반출 정보 선택
  • 제목
  • URL
돌아가기
확인
취소
  • 개인휴대통신에서 이동국의 수신성능개선을 위한 시스템 분석
  • System Analysis for Receiving Performance Improvement of Mobile Station in PCS
저자명
주재한,박세승,박종안,천종훈,Ju. Jae-Han,Park. Se-Seung,Park. Jong-An,Cheon. Jong-Hun
간행물명
정보처리논문지
권/호정보
1999년|6권 1호|pp.159-166 (8 pages)
발행정보
한국정보처리학회
파일정보
정기간행물|
PDF텍스트
주제분야
기타
이 논문은 한국과학기술정보연구원과 논문 연계를 통해 무료로 제공되는 원문입니다.
서지반출

기타언어초록

본 논문에서는 개인휴대통신(PCS)의 최소 규격인 J-STD-018을 기준으로 하여 수신기의 수신감도, 단일톤 둔감도, 상호변조 스퓨리어스에 의한 응답감쇄 규격에서 각각 잡음지수와 제 3고조파 차담점을 구하고 시뮬레이션을 통하여 분석하였다. 시뮬레이션 결과 수신감도 규격에서는 전체 잡음지수가 5.99dB이고 제 3고조파 차단점은 -33.979dBm이었다. 또한 단일톤 둔감도 및 상호 변조 스퓨리어스에 의한 응답감쇄 규격에는 전제 잡음지수가 0.367dBm이고 제 3고조파 차단점은 6.989 이 증가되었다. 이것은 잡음지수보다 제 3고조파 차단점이 훨씬 증가 되므로 간섭톤과 밀접한 관계가 있는 소자인 Mixer는 제 3고조파 차단점을 높게 규정하고 IF SAW 필터의 중심 주파수로부터 1.25MHz와 2.05MHz지점인 곳에 감쇄가 456dB이상 되어야 함을 보였다.

기타언어초록

In this paper, we examined noise figure and the 3rd order intercept point in sensitivity single tone desensitization, and response attenuation by intermodulation spurious of receiver and also analyzed them through simulation based on J-STD-0.18, which is the minimum specification of PCS mobile station. The result of simulation was as follows ; In sensitivity specification, the total noise figure was 5.99dB and the 3rd order intercept point was -33.979dB. Ins ingle tone desensitization and intermodulation spurious response attenuation specification, the total noise figure was 6.375dB and the 3rd order intercept point was -26.99dBm. When there is an interference tone, the nosie figure and the 3rd order intercept point have been increasedly 0.367dB respectively, compared wit that of no interference tone. Because the amount of increase in the 3rd order intercept point was highly raised more than that of noise figure, mixer, closely related to interference tone should be specified in high 3rd order intercept point. At a frequency spacing of 1.25MHz and 2.05MHz from center frequency in IF SAW filter, attenuation should be more than 45dB.