기관회원 [로그인]
소속기관에서 받은 아이디, 비밀번호를 입력해 주세요.
개인회원 [로그인]

비회원 구매시 입력하신 핸드폰번호를 입력해 주세요.
본인 인증 후 구매내역을 확인하실 수 있습니다.

회원가입
서지반출
강원도 간성-현내 지역 화강암류 비탈면 안정성 검토 사례 연구
[STEP1]서지반출 형식 선택
파일형식
@
서지도구
SNS
기타
[STEP2]서지반출 정보 선택
  • 제목
  • URL
돌아가기
확인
취소
  • 강원도 간성-현내 지역 화강암류 비탈면 안정성 검토 사례 연구
저자명
김홍균,김승현,옥영석,구호본,Kim. Hong-Gyun,Kim. Seung-Hyun,Ok. Young-Seok,Koo. Ho-Bon
간행물명
지질공학
권/호정보
2012년|22권 3호|pp.331-341 (11 pages)
발행정보
대한지질공학회
파일정보
정기간행물|
PDF텍스트
주제분야
기타
이 논문은 한국과학기술정보연구원과 논문 연계를 통해 무료로 제공되는 원문입니다.
서지반출

기타언어초록

화강암류 암석은 일반적으로 절리 발달이 미약하고 단층파쇄대가 잘 발달하지 않는 등 공학적으로 양질의 암석에 해당된다. 그러나 산학지구 붕괴 비탈면을 구성하는 지반은 화강암류로 구성되었음에도 불구하고, 깊은 토사층을 가지며, 불연속면이나 단층 등의 지질구조는 거의 관찰되지 않고, 표층붕괴가 발생한 형태에 해당된다. 본 비탈면의 안정성 고찰을 위해 3가지 경우(현재 단면, 최초 설계 단면, 수정 설계 단면)에 대한 강우지속시간과 간극수압 변화, 안전율 등에 관한 해석을 수행하였다. 강우 지속시간이 길어질수록 지하수위는 높이 20 m까지 상승하는 것으로 나타났으며, 최초 설계단계 단면의 2일 지속강우 기간에는 안전율이 확보되는 것으로 확인되지만, 4일 강우지속기간 동안에는 허용안전율을 만족하지 못하는 것으로 확인되었다. 수정 설계 단면에서는 4일 강우지속기간에도 안전율이 확보되므로 산학 지구는 1:1.8 경사도로 절취하는 것이 영구적인 안정성을 확보하는 방안이라고 판단된다.

기타언어초록

Granitoid rocks are generally high-quality rock from a geotechnical perspective, because they rarely contain systematic joints or fragmented fault zones. Although the rock type at the Sanhak site is granite, a collapsed slope has a deep soil layer and shows no residual structures such as discontinuities or faults; surface avalanches from this slope can be observed in several places. To study the stability of this slope, we investigated rainfall duration, variation in pore-water pressure, and the factor of safety considering three cases (current cross-section, initial planning cross-section, revised planning cross-section). With increasing duration of rainfall, the groundwater level rises, up to 20 m in height from ground surface. In the initial planning cross-section, safety was secure for rainfall of 2 days duration, but inadequate for rainfall of 4 days duration. In the revised planning cross-section, however, safety factors were secure for rainfall of 4 days duration. Therefore, to ensure permanent stability at the Sanhak site, a slope degree of 1:1.8 should be maintained during cutting.