기관회원 [로그인]
소속기관에서 받은 아이디, 비밀번호를 입력해 주세요.
개인회원 [로그인]

비회원 구매시 입력하신 핸드폰번호를 입력해 주세요.
본인 인증 후 구매내역을 확인하실 수 있습니다.

회원가입
서지반출
이중 모드 ADC를 이용한 U-Health 시스템용 맥박수와 맥박파형 검출 회로 설계
[STEP1]서지반출 형식 선택
파일형식
@
서지도구
SNS
기타
[STEP2]서지반출 정보 선택
  • 제목
  • URL
돌아가기
확인
취소
  • 이중 모드 ADC를 이용한 U-Health 시스템용 맥박수와 맥박파형 검출 회로 설계
저자명
신영산,위재경,송인채,Shin. Young-San,Wee. Jae-Kyung,Song. Inchae
간행물명
Journal of the Institute of Electronics Engineers of Korea
권/호정보
2013년|50권 9호|pp.68-73 (6 pages)
발행정보
대한전자공학회
파일정보
정기간행물|
PDF텍스트
주제분야
기타
이 논문은 한국과학기술정보연구원과 논문 연계를 통해 무료로 제공되는 원문입니다.
서지반출

기타언어초록

본 논문에서는 수면 중에 사용자의 건강상태를 모니터링 하기 위한 U-health 시스템으로 맥박 수와 맥박 파형 검출 회로를 제안하였다. 제안된 검출 회로의 출력은 배터리의 교체 없이 장시간 사용하기 위하여 건강 상태에 따라 맥박 수 또는 맥박 파형이 선택된다. 이러한 동작을 위해 제안된 신호 검출 회로는 ADC 모드 또는 카운트 모드로 동작하는 이중 모드 ADC와 간단한 디지털 로직으로 구성된 판별기를 사용하였다. 우선 초기에는 카운트 모드로 동작하는 이중 모드 ADC를 통해 4초 동안의 맥박 수를 검출한다. 검출된 맥박수는 판별기에서 1분간 누적한 뒤 건강 상태를 판별한다. 건강 이상 등으로 맥박 수가 설정된 정상 범위를 벗어난 경우 이중 모드 ADC는 ADC 모드로 동작하며 맥박 파형을 1kHz의 샘플링 주파수로 10bit의 디지털 데이터로 변환한다. 데이터는 버퍼에 저장하였다가 620kbps의 속도로 RF Tx를 통해 단말기로 전송한다. 이때 RF Tx는 모드에 따라 1분 혹은 1ms 간격으로 동작한다. 제안된 신호 검출 회로는 $0.11{mu}m$ 공정으로 설계하였으며 $460{ imes}800{mu}m^2$의 면적을 차지한다. 측정결과 제안된 검출 회로는 1V의 동작 전압에서 카운트 모드에서는 $161.8{mu}W$, ADC 모드에서는 $507.3{mu}W$의 전력을 소모한다.

기타언어초록

In this paper, we proposed a readout circuit of pulse waveform and rate for a U-health system to monitor health condition. For long-time operation without replacing or charging a battery, either pulse waveform or pulse rate is selected as the output data of the proposed readout circuit according to health condition of a user. The proposed readout circuit consists of a simple digital logic discriminator and a dual-mode ADC which operates in the ADC mode or in the count mode. Firstly, the readout circuit counts pulse rate for 4 seconds in the count mode using the dual-mode ADC. Health condition is examined after the counted pulse rate is accumulated for 1 minute in the discriminator. If the pulse rate is out of the preset normal range, the dual-mode ADC operates in the ADC mode where pulse waveform is converted into 10-bit digital data with the sampling frequency of 1 kHz. These data are stored in a buffer and transmitted by 620 kbps to an external monitor through a RF transmitter. The data transmission period of the RF transmitter depends on the operation mode. It is generally 1 minute in the normal situation or 1 ms in the emergency situation. The proposed readout circuit was designed with $0.11{mu}m$ process technology. The chip area is $460{ imes}800{mu}m^2$. According to measurement, the power consumption is $161.8{mu}W$ in the count mode and $507.3{mu}W$ in the ADC mode with the operating voltage of 1 V.